Narrow Results

Cadmium sulphide (CdS) nanocrystallites were prepared by sulphuration route with capping in polyethylene oxide (PEO) polymer matrix. It is found that PEO could provide a confined environment for particle nucleation and growth of CdS nanocrystallites. The scanning electron microscopy (SEM) with energy dispersive analysis by X-ray (EDAX) studies confirms the presence of CdS nanocrystallites in polymer matrix. X-ray diffraction (XRD) studies and transmission electron microscopy (TEM) selected area diffraction (SAD) patterns show that these crystallites have hexagonal structure. The TEM and UV-Visible absorption studies indicate uniform size distribution having size around 2.3 nm and band gap of 2.7 eV. X-ray photoelectron spectroscopy (XPS) studies reveal that core level energy positions of the Cd is shifted towards the lower binding energy and has similar chemical environment to that of bulk CdS.

A novel and shape-controlled synthesis method for uniformly-shaped poly(p-phenylenediamine) (PpPD) microparticles was developed using (NH₄)₂S₂O₈ (APS) as an oxidant. The results demonstrated that the morphologies of PpPD varied from nanofibers to nanospheres and nest-like microspheres by tuning the pH of solution. Tiny pH change leads to the significant change in product morphology. The structure of microspheres is similar to graphene which was first discovered. Further study showed that the PpPD nanofibers were dimer. The difference in the structure of PpPD nanofibers and nanospheres (microspheres) resulted in different solubility in water. The nanosized oligomer crystallites served as starting templates for the nucleation of PpPD nanofibers. Further growth of nanofibers was proceeded by the self-organization of phenazine units or their blocks located at the ends of the PpPD chains.

The electrochemical properties of poly sodium 4-styrenesulfonate intercalated graphite oxide (PSSGO) have been investigated in a 1 M H₂SO₄ electrolyte. We observed capacitor behavior at scan rate of 1–25 mV/s in a cyclic voltammetry. Specific capacitance obtained from galvanostatic charge and discharge measurements were 6 F/g to 102 F/g at 1 A/g to 0.1 A/g, respectively. The specific capacitance of PSSGO is relatively high compared to that of the precursor graphite oxide in which the specific capacitance was 11–20 F/g at 0.03 A/g. Capacitance retention was 73% after 3000 cycles, proving reliable cyclic stability up to 3000 cycles.

Amphiphilic polymer carriers (PEG–St–$R$) were prepared from cassava starch and their pH response was investigated. First, hydrophobic tapioca starch polymer (St–$R$) was prepared with octyl acyl as the hydrophobic group. The hydrophilic group polyethylene glycol (mPEG) was then introduced into the polymer by esterification to produce amphiphilic tapioca starch polymer (PEG–St–$R$). Its self-assembly behavior was characterized using fluorescent probes. The morphology of PEG–St–$R$ was investigated by transmission electron microscopy (TEM). Loading of the anti-cancer drug curcumin was used to assess the delivery and slow-release performance of the amphiphilic tapioca starch polymer. Cumulative drug release was explored at various pH conditions, with the greatest release from drug-loaded micelles being observed under acidic conditions and stable in a neutral environment. These results provide a theoretical basis for the preparation of pH-responsive nanomicelle carriers, and a platform for the preparation of novel amphiphilic starch-based polymers.

Devices such as solar and fuel cells have been studied for many decades and noticeable improvements have been achieved. This paper proposes a Micro Photosynthetic Power Cell (μPSC) as an alternative energy-harvesting device based on photosynthesis of blue-green algae. The effect of important biodesign parameters on the performance of the device, such as no-load performance and voltage–current (V–I) characteristics, were studied. Open-circuit voltage as high as 993 mV was measured while a peak power of 175.37 μW was obtained under an external load of 850 Ω. The proposed μPSC device could produce a power density of 36.23 μW/cm², voltage density of 80 mV/cm² and current density of 93.38 μA/cm² under test conditions.

Membrane technologies are essential for water treatment, bioprocessing and chemical manufacturing. Stimuli-responsive membranes respond to changes in feed conditions (e.g., temperature, pH) or external stimuli (e.g., magnetic field, light) with a change in performance parameters (permeability, selectivity). This enables new functionalities such as tunable performance, self-cleaning and smart-valve behavior. Polymer self-assembly is a crucial tool for manufacturing such membranes using scalable methods, enabling easier commercialization. This review surveys approaches to impart stimuli responsive behavior to membrane filters using polymer self-assembly.

Nowadays tools based on Scanning Probe Methods (SPM) have become indispensable in a wide range of applications such as cell imaging and spectroscopy, profilometry, or surface patterning on a nanometric scale. Common to all SPM techniques is a typically slow working speed which is one of their main drawbacks. The SPM speed barrier can be improved by operating a number of probes in parallel mode. A key element when developing probe array devices is a convenient read-out system for measurements of the probe deflection. Such a read-out should be sufficiently sensitive, resistant to the working environment, and compatible with the operation of large number of probes working in parallel. In terms of fabrication, the geometrical uniformity i.e. the realisation of large numbers of identical probes, is a major concern but also the material choice compatible with high sensitivity, the detection scheme and the working environment is a challenging issue. Examples of promising applications using parallel SPM are dip-pen-nanolithography, data storage, and parallel imaging.