International Journal of Computational Materials Science and Engineering

The effect of axial magnetic field along with axial temperature gradient, in a confined cylindrical cavity packed with incompressible electrical conducting fluid having a top rotating lid, has been investigated. Due to the presence of axial magnetic field, Joule heating effect is considered in this study. The governing parameters ranges are as follows: $1\le J\le 8$, $1\le \mathrm{\text{Ri}}\le 10$ at Re$=$1000, Pr$=$0.015. It is found that the internal heat generation due to Joule heating in mixed convection is governed by interaction parameter and temperature gradient. However, the Joule heating effect has very less effect on primary flow in comparison to the secondary flow along the meridional plane.

Cellular solid materials are progressively becoming more predominant in lightweight structural applications as more technologies realize these materials can be improved in terms of performance, quality control, repeatability and production costs, when allied with fast developing manufacturing technologies such as Additive Manufacturing. In parallel, the rapid advances in computational power and the use of new numerical methods, such as Meshless Methods, in addition to the Finite Element Method (FEM) are highly beneficial and allow for more accurate studies of a wide range of topologies associated with the architecture of cellular solid materials. Since these materials are commonly used as the cores of sandwich panels, in this work, two different topologies were designed — conventional honeycombs and re-entrant honeycombs — for 7 different values of relative density, and tested on the linear-elastic domain, in both in-plane directions, using the Natural Neighbor Radial Point Interpolation Method (NNRPIM), a newly developed meshless method, and the Finite Element Method (FEM) for comparison purposes.

New plastic solutions for the bearing capacity factors of conical footings on rock masses obeying the Hoek–Brown yield criterion are presented in the paper by using the lower and upper bound finite element limit analysis. A conical footing has a cone apex angle and is penetrated into a rock mass. The considered dimensionless parameters include the cone apex angle, the yield parameter, and the geological strength index of a rock mass, where the effects of these dimensionless parameters on the bearing capacity factor are compressively investigated. The collapse mechanisms of conical footings on rock masses are examined and discussed in the paper.

This paper presents a mathematical model to study forced imbibition and examine the correlation between spontaneous and forced imbibition in a water-wet heterogeneous porous media. An explicit approximate analytical method with its convergence analysis is proposed here to obtain an analytic expression for the saturation profile of the wetting phase along with its case study to discuss the potential effects and reliability of the viscosity ratio, wettability state of the medium, capillary pressure and relative permeability of the phases on forced imbibition phenomenon. Finally, the simulation results investigate the impact of all parameters on the hydrocarbon reservoir’s saturation rate and recovery rate during the forced imbibition process.

This paper presents a method for determining material constants of hyperelastic material used for building the soft robotic actuators. Sixty testpieces were made of silicone rubber with a shore A hardness from 20 A to 45 A. Each of them was then subjected to the uniaxial tensile test to obtain the stress–strain relationship, which is a key factor to evaluate the compatibility of the common six forms of strain energy density function for hyperelastic material. The sum of square error was used to determine the most relevant constitutive models, which are Ogden third order, Polynomial second order, and Yeoh, as well as parameter values of the corresponding materials. To analyze the appropriateness of these models for computation, six pneumatic soft actuators were built from materials with different hardness and tested for various pressures. From the simulation and experimental results, the model Yeoh has yielded the highest accuracy. This outcome forms a firm basis for the determination of suitable material in the computation and simulation of the pneumatic soft actuator. Besides, the obtained experimental results in this paper could be included in the database of hyperelastic material with different hardness for further simulation in the related field.

We have extended a computational model used to research the thermodynamic properties of binary liquid alloys to study chemical short-range order parameters and diffusion coefficients. Numerous simulations have also been employed for surface properties such as surface concentration and surface tension. The propensities for phase separation of the Pb–Sb alloy were also observed with a temperature rise. The structural and thermodynamic properties of the alloys were measured using the same interaction parameters that are suitable for the free energy of mixing and mixing enthalpy. The interaction parameters are discovered to be temperature-dependent but concentration-independent. Our results indicate that the liquid alloy Pb–Sb has a weakly interacting composition. According to the surface property review, the element Sb having a higher surface concentration than its bulk concentration segregates over the surface of the alloy.