Narrow Results

The effects of microstructures of Ti-6Al-4V alloy on the flow stresses and fracture behaviors at quasi-static and dynamic deformation conditions were investigated. Specimens of different sizes and fractions of α globules in equiaxed and bimodal structures were compressed at the strain rate of 2×10⁻³/s and 3×10³/s using hydraulic testing machine and split Hopkinson pressure bar, respectively. The a globule size in equiaxed structure changed the level of flow stresses, but did not affect the strain hardening characteristics. Meanwhile, the volume fraction of α globule (or lamellar phase) in bimodal structures influenced both the flow stress and strain hardening exponent at quasi-static and dynamic deformation conditions. Bimodal structure of 50% lamellar fraction is considered to be more favorable in dynamic deformation condition at strain rate regime of 3×10³/s than equiaxed or bimodal one having higher lamellar fraction.

The sensitivity of the flow stress of polymers to strain-rate is one of the major concerns in mechanics of materials since polymers and polymer matrix composites are widely used in many engineering applications. In this paper, we present tests on Nylon 6 and Nylon 66 on wide range of strain-rates (0.001-5000s⁻¹). Specifically, we used INSTRON machine for low strain-rates. The high strain-rate measurements were inferred from the Hopkinson bar tests. Only the compressive behaviour was investigated. To eliminate any interference with temperature and humidity effects, test samples were conditioned at 20°C and 50% of hygrometry. Moreover, the effects of the specimen geometry were considered. The current study results are also compared to values found in literature.

A material identification program AFDEX/MAT is presented in this paper. The program is based on the method for acquiring true stress-strain curves over large range of strains using engineering stress-strain curves obtained from a tensile test coupled with a finite element analysis. In the method, a tensile test is analyzed using a rigid-plastic finite element method combined with a perfect analysis model for its associated simple bar to provide the information of deformation. An initial reference true stress-strain curve, which predicts the necking point exactly, is modified iteratively to minimize the difference in tensile force between the experiments and predictions of the tensile test. It was applied to identifying the mechanical behaviors of two new pre-heat treated steels of ESW95 and ESW105 and a conventional Cr-Mo steel of SCM435. The predictions are compared with the experiments for the tensile test of the three materials, showing an excellent similarity.

Tensile deformation behavior of ultrafine-grained (UFG) copper processed by accumulative roll-bonding (ARB) was studied under different strain rates at room temperature. It was found that the UFG copper under the strain rate of 10${}^{-2}$ s${}^{-1}$ led to a higher strength (higher flow stress level), flow stability (higher stress hardening rate) and fracture elongation. In the fracture surface of the sample appeared a large number of cleavage steps under the strain rate of 10${}^{-3}$ s${}^{-1}$, indicating a typical brittle fracture mode. When the strain rate is 10${}^{-2}$ or 10${}^{-1}$ s${}^{-1}$, a great amount of dimples with few cleavage steps were observed, showing a transition from brittle to plastic deformation with increasing strain rate.

The hot flow stress of as-quenched Al-Cu-Mn alloy was modeled using the constitutive equations. The as-quenched Al-Cu-Mn alloy were treated with isothermal hot compression tests in the temperature range of 350–500°C, the strain rate range of 0.001–1 s^-1. The hyperbolic sine equation was found to be appropriate for flow stress modeling and prediction. Based on the hyperbolic sine equation, a constitutive equation is a relation between 0.2 pct yield stress and deformation conditions (strain rate and deformation temperature) was established. The corresponding hot deformation activation energy (Q) for as-quenched Al-Cu-Mn alloy was determined to be 251.314 kJ/mol. Parameters of constitutive equation of as-quenched Al-Cu-Mn alloy were calculated at different small strains (≤ 0.01). The calculated flow stresses from the constitutive equation are in good agreement with the experimental results. Therefore, this constitutive equation can be used as an accurate temperature-stress model to solve the problems of quench distortion of Al-Cu-Mn alloy parts.

A material identification program AFDEX/MAT is presented in this paper. The program is based on the method for acquiring true stress-strain curves over large range of strains using engineering stress-strain curves obtained from a tensile test coupled with a finite element analysis. In the method, a tensile test is analyzed using a rigid-plastic finite element method combined with a perfect analysis model for its associated simple bar to provide the information of deformation. An initial reference true stress-strain curve, which predicts the necking point exactly, is modified iteratively to minimize the difference in tensile force between the experiments and predictions of the tensile test. It was applied to identifying the mechanical behaviors of two new pre-heat treated steels of ESW95 and ESW105 and a conventional Cr-Mo steel of SCM435. The predictions are compared with the experiments for the tensile test of the three materials, showing an excellent similarity.