Narrow Results

The influence of anodized film on corrosion and electrochemical behavior of extruded magnesium alloy AZ63, cast and die-cast magnesium alloys AZ91D were investigated by using immersion technique, electrochemical methods, SEM, EDAX, IR and XRD. The results showed anodized film could improve remarkably corrosion resistance. Protection effect was different with the same anodizing process because formation status of anodized film of different materials was different. The formation status of anodized film was related to alloy microstructure as revealed by optical and scanning electron microscopy. The formatting process and casting method strongly influences the corrosion performance by affecting on the alloy microstructure. A tentative corrosion mechanism is presented explaining the corrosion behavior of anodized magnesium alloy.

The McMurry crossed coupling reactions of p,p′-disubstituted benzophenones (1) with pivalaldehyde (Pv) gave the corresponding ethenes (2) in fair to excellent yield. The observed geometrical selectivity is varied depending on a kind of p-substituent of the aromatic moiety of 1, when p′-substituent is limited to methyl. According to the known reaction mechanism, the reason why the geometry selection occurred is discussed by a conformational analysis of a possible intermediate, titanium bound pinacolate, and molecular orbital calculations of the starting carbonyl compounds. As a result, the selection is caused by electronic and stereochemical structures of anion radical of 1 and approaching mode of Pv anion radical to them. Distribution of a spin density and unsymmetrical nature of two aromatic moieties of anion radical of 1 provide predetermined pathway to bring about the pinacolate without any rotational conversion under the reaction conditions. Subsequent workup affords 2 with the observed geometry.

The charge-transfer reaction of tetraarylbutatriene 1 with tetracyanoethene (TCNE) in dichloromethane at room temperature was studied and we found a novel addition reaction. A red crystalline material 2 was isolated as an intermediate product which is converted slowly into dihydronaphthalene derivative 3 in dichloromethane but rapidly in protic solvent. The structure of the compounds was determined by X-ray crystallography. The detailed structure and the plausible reaction mechanism have also been discussed.

Nanocrystalline Cu particles were prepared by mechanochemical reduction of cuprite (CU₂O) with graphite in a high-energy ball mill. In order to gain an understanding into the possible mechanisms, the kinetic of the process was investigated using Johnson-Mehl-Avrami (JMA) model. It can be seen that theoretical calculation agrees well with experimental data. It was found that the most important effect of mechanical activation is the formation of the lattice defects and grain boundaries in addition to activated fresh surface areas during milling, which promote the reduction process. The Cu nanopowder was characterized using X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD and TEM results showed the nano-structure nature of the product processed under the synthesis conditions; the crystallite size was measured almost 30 nm in the 30 h milled powders.

This paper explores the mechanism design of a balloon machine representing a vending machine where consumers can select their desired shapes, as well as avoid bursting caused by manual inflation. Inside the machine, balloons are placed on the mechanism designed based on a waterwheel which rotates at a constant speed generated by motion among different sizes of gears. When rotating to the corresponding shaped balloon, the inflator will move under the opening to pull it out from the display point and start to inflate the balloon for the set number of seconds. After the inflation is completed, the glass door will open and the customer can take out their balloon. The main purpose of our development and design of the balloon machine is to improve the general balloon blowing and it is easy to prevent over-exposure and blast. The balloon machine can automatically inflate and detect the blowing time to improve the shortcomings of the balloon’s blast. In this way, it can effectively decrease sudden explosions and the number of frightened people.

Pedestrian-car interweaving is a prominent problem in old residential communities in Chinese cities. To achieve a better pedestrian-car separation to create a safe and comfortable living environment in old residential communities, this paper investigated the mechanism of the flows of pedestrians and cars on a road network inside an old residential community. A method for calculating the flows of pedestrians and cars was proposed to identify the road segments or nodes where the pedestrian flows are interlaced or intersected with the vehicle flows. This method was applied to the estimation of the traffic in the Wangyuehu Community of Changsha City, China. The estimated distribution of community network traffic and pedestrian-car interweaving sites was consistent with the actual situation.