Narrow Results

Fiber metal laminates (FMLs) belong to a class of composite materials comprising layers of metal sheets and fiber-reinforced polymers (FRP), configured in a specific sequence. This study investigates the tensile strength of FML specimens joined by riveted joints. FML plates were fabricated using AA5052 aluminium alloy, E-glass fibers, epoxy resin, and layered double hydroxide (LDH) via a hand layup process. The experimental parameters included the pattern of rivets, type of rivet materials, and rivet size. Tensile strength, the output response, was evaluated using Taguchi’s L₉ orthogonal array design, followed by testing on a universal testing machine. The main effect plot and 3D surface plots were employed to analyze the tensile test results. Maximum tensile strength was held by the test specimen which was connected by the rivets made up of mild steel. From the ANOVA results presented in Table 6, it was inferred that the number of rivets used for joining the FML specimens (pattern) played a major role in deciding the tensile strength of the specimens (57.25%). A regression equation, derived from Design Expert software, established the relationship between input variables and the tensile strength of FML specimens. ANOVA was conducted to assess the impact of each process variable on achieving optimal tensile strength.

This research contributes novelty by integrating LDH into FML fabrication and demonstrates practical significance through systematic optimization of riveting parameters to enhance tensile strength. Quantitative and qualitative analyses underscore the effectiveness of the proposed FML configuration, validating its potential for structural applications.

A material identification program AFDEX/MAT is presented in this paper. The program is based on the method for acquiring true stress-strain curves over large range of strains using engineering stress-strain curves obtained from a tensile test coupled with a finite element analysis. In the method, a tensile test is analyzed using a rigid-plastic finite element method combined with a perfect analysis model for its associated simple bar to provide the information of deformation. An initial reference true stress-strain curve, which predicts the necking point exactly, is modified iteratively to minimize the difference in tensile force between the experiments and predictions of the tensile test. It was applied to identifying the mechanical behaviors of two new pre-heat treated steels of ESW95 and ESW105 and a conventional Cr-Mo steel of SCM435. The predictions are compared with the experiments for the tensile test of the three materials, showing an excellent similarity.

In this study, strong {0002} textured (or strong ND//<0002> textured) AZ31 Mg alloy sheets were prepared. These AZ31 Mg alloy sheets were cut along the angles of 0, 12.5, 25, 30 and 37.5 degrees to the rolling direction or {0002} texture. Prepared samples with different angles to the rolling direction were rolled at room temperature and after subsequent heat treatment, the bendability, ultimate tensile stress, elongation and texture are investigated using the 3-points bending tester, tensile tester and x-ray diffractometer, respectively. The specimen having along the angles of 0 degree to the rolling direction shows the highest load and 45 degrees specimen shows the highest displacement among any other specimens in the bending test. The specimen having along the angles of 12.5 and 25 degrees to the rolling direction shows highest elongation and of 0 degree specimen shows the highest ultimate tensile stress among any other specimens after cold rolling and subsequent heat treatment at 150°C for 30 minutes in bending test.

The microstructure, pole figure and r-value of the frictionally rolled and subsequently heat treated AA 5052 Al sheets were investigated by optical microscopy, x-ray diffractometer and tensile tester, respectively. Frictionally rolled AA 5052 Al specimens showed a fine grain size. After subsequently heat treated specimens, the ND//<111> texture component was increased. The r-values of the frictionally rolled and subsequently heat treated Al alloy sheets were about two times higher than those of the original Al sheets. These could be related to the formation of ND//<111> texture components through frictional rolling in and subsequent heat treatment of AA 5052 Al sheet.

The purpose of experiment was to produce bulk nanocrystalline Zn by mechanical attrition. The bulk nanocrystalline Zn produced by mechanical attrition was studied. The microstructural evolution during cryomilling and subsequent room temperature milling was characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD). In this paper, Nanocrystalline Zn was produced by insitu consolidation of Zn elemental powder using mechanical attrition at liquid nitrogen and room temperature. For the samples studied, the longest elongation of 65% and highest stress of 200 MPa is obtained in nanocrystalline Zn during tensile testing at the condition of strain rate (10^-3 sec^-1) and 20°C which is equal to 0.43 T_m (T_m is the melting temperature of pure Zn).

In this study, a system for non-contact in-situ measurement of strain during tensile test of thin films by using CCD camera with marking surface of specimen by black pen was implemented as a sensing device. To improve accuracy of measurement when CCD camera is used, this paper proposed a new method for measuring strain during tensile test of specimen with micrometer size. The size of pixel of CCD camera determines resolution of measurement, but the size of pixel can not satisfy the resolution required in tensile test of thin film because the extension of the specimen is very small during the tensile test. To increase resolution of measurement, the suggested method performs an accurate subpixel matching by applying 2nd order polynomial interpolation method to the conventional template matching. The algorithm was developed to calculate location of subpixel providing the best matching value by performing single dimensional polynomial interpolation from the results of pixel-based matching at a local region of image. The measurement resolution was less than 0.01 times of original pixel size. To verify the reliability of the system, the tensile test for the BeNi thin film was performed, which is widely used as a material in micro-probe tip. Tensile tests were performed and strains were measured using the proposed method and also the capacitance type displacement sensor for comparison. It is demonstrated that the new strain measurement system can effectively describe a behavior of materials after yield during the tensile test of the specimen at microscale with easy setup and better accuracy.

We performed the tensile test of an individual carbon nanofiber (CNF) inside a scanning electron microscope. The mechanical testing system was installed in a scanning electron microscope (SEM). The nano-manipulator was set up in the SEM, and the force sensor, which is formed as a cantilever, was mounted on the nano-manipulator. Then, the force sensor can be controlled by using the nano-manipulator. The CNFs were dispersed on the transmission electron microscope (TEM) grid, and the both end of the CNFs were welded on the TEM grid and the tip of force sensor by exposing electron-beam of the SEM. The tensile test of the CNFs was performed by controlling the nano-manipulator. The load response during the tensile test was obtained by force sensor. Stess-strain curve was obtained from force-displacement curve of CNF after tensile test. The elastic modulus of CNFs was calculated at ~12.5 GPa.

This paper aims to investigate the impact of moisture on mechanical properties of insulation paper. According to the molecular modeling approach proposed by Theodorou, the amorphous cellulose models of insulation paper with different moisture contents were built up to calculate mechanical parameters and hydrogen bond networks. And relevant conclusions could be drawn through further analysis on these calculation results: water molecules can destroy hydrogen bond network between the neighboring cellulose molecules, which might be responsible for the significant decrease of Young's modulus and other mechanical parameters, while no appreciable effect of intramolecular hydrogen bonds on mechanical properties was detected. Thus tensile tests were also carried out to study the moisture influence on the Young's modulus, by which the result of the simulation was approved.

The molecular dynamics method is used to investigate the formation and properties of irradiation-induced damage (point defects). Displacement cascade simulations are performed to study the effects of primary knock-on atom (PKA) energy, temperature, vacancy concentration and tensile pre-strain on irradiation-induced damage in $\alpha$-Fe. An increase in PKA energy, vacancy concentration and tensile pre-strain can lead to an increase in defect numbers. In contrast, an increase in temperature decreases the defect numbers. After cascade collisions, tensile tests are performed to investigate the effect of point defects on mechanical properties. The yield stress and corresponding strain of irradiated Fe decrease with an increase in the number density of Frenkel pairs. Results show that irradiation accelerates damage of the internal structure, decreases the number of slip bands and increases the instability of the structure during plastic deformation.

This paper introduces a procedure to predict failure strain for an arctic class marine structural steel, EH36. Based on previous results,^1-4 this paper explains formulation procedure for a failure strain curve of the EH36 in medium-low and high average stress triaxiality zones by performing tensile tests for round and flat specimens with various notches. Verification of the validity of the failure strain envelope using user-defined subroutine imbedded in commercial finite element code Abaqus/Explicit is also described. The failure strain envelope provides relatively accurate simulation results by comparing tensile test results of asymmetric notch structures with fracture simulations using the user-defined subroutine.

A method to quantify crazing deformations by tensile tests for polystyrene (PS) and polyolefin elastomer (POE) blends was investigated. The toughness of PS/POE blends, reflected by the Charpy impact strength, increased with the content of POE. SEM micrographs showed the poor compatibility between PS and POE. In simple tensile tests, it is very easy to achieve the ratio of crazing deformation, i.e.K by measuring the size changes of samples. The K values decreased with increasing the content of POE, and the deformations of PS/POE blends were dominated by crazing. The plots of the change of volume (ΔV) against longitudinal variation (Δl) showed a linear relationship, and the slope of lines decreased with the content of POE. Measuring samples at the tensile velocities of 5 mm/min, 50 mm/min, and 500 mm/min respectively, the K values kept unchanged for each PS/POE blends.

Effect of the hydrogen-charging on the uniaxial tensile behaviors of a ductile cast iron was investigated. It was found that the hydrogen-charging accelerated the process of crack growth from graphite in the uniaxial tensile loading condition. Further, the accelerated crack growth had a marked influence on the reduction of area at the final fracture (RA) of specimens. For instance, for the uncharged specimens, the RA was nearly constant irrespective of the strain rate. In contrast, for the hydrogen-charged specimens, the RA gradually decreased as the strain rate decreased. Thermal desorption spectroscopy and hydrogen microprint technique revealed that, in the hydrogen-charged specimen, most of solute hydrogen was diffusive one, which was mainly segregated at graphite, graphite/matrix interface zone and pearlite. Based on these experimental observations, we consider that the hydrogen-induced degradation behavior was caused mainly by a combination of the following three mechanisms: (i) supplement of hydrogen to the crack tip from graphite and graphite–matrix interface, (ii) hydrogen-enhanced pearlite cracking and, (iii) successive hydrogen-emission from graphite and additional hydrogen-supplement to the crack tip.

Lead-free piezoelectric (Bi_1/2Na_1/2)TiO₃ (abbreviated as BNT) films were deposited on 1 mm thick pure titanium(Ti) substrates by a hydrothermal method. Tensile tests were performed to quantitatively assess the adhesion strength between BNT films and Ti substrates. Ti substrates were pretreated by chemical polish and mechanical polish respectively prior to BNT film deposition. In the tensile test, the behavior of BNT film exfoliation was investigated by the replica method. The critical Ti substrate strain inducing BNT film exfoliation was determined by the aid of finite element analysis (FEM). In this study, the results revealed that BNT film exfoliations were caused by the strain of Ti substrate, and the mechanical polish pretreatment improved the adhesion of BNT film to Ti substrate.

Through the Split Hopkinson Pressure Bar (SHPB) test and the quasi-static tensile test on non-standard specimen of titanium alloy Ti-6Al-4V, the rules of the mechanical property changing with the specimen size under different temperatures are summarized, and the parameters of the classical constitutive Johnson-Cook (JC) model are determined. Based on the dislocation pile-up theory, the classical constitutive JC model is modified by considering the influence of grain size, and the modified JC model is established by adding a functional term Δσ into the classical constitutive model to describe the influence of the grain. The tensile testis analyzed by the finite element method (FEM) simulation. Comparing with the experimental results, the simulation results based on the modified JC model show much better accuracy than that by the classical JC model.

Snake rolling is a newly developed asymmetrical rolling technique which has both different speed ratio and horizontal offset distance. But the industrial application of the snake rolling is still on its way because it needs completed science researching. The combination of the snake rolling and the 2024 T39 process on the mechanical properties of the final product is investigated in this paper. Multi-pass snake rolling was conducted in our work. Compared with the same plate in conventional rolling, The tensile strength shows almost the same. But the Kahn tear test evidently showed that snake rolling improves the Unit Initiation Energies of the 2024 aluminum alloy plate dramatically by 60.5% in average, and, without loss its strength. Moreover, the snake rolling also reduced the anisotropy of UIE in maximum 63.0%, compared to conventional rolling, owing to the stronger {111}//ND shear texture.

A material identification program AFDEX/MAT is presented in this paper. The program is based on the method for acquiring true stress-strain curves over large range of strains using engineering stress-strain curves obtained from a tensile test coupled with a finite element analysis. In the method, a tensile test is analyzed using a rigid-plastic finite element method combined with a perfect analysis model for its associated simple bar to provide the information of deformation. An initial reference true stress-strain curve, which predicts the necking point exactly, is modified iteratively to minimize the difference in tensile force between the experiments and predictions of the tensile test. It was applied to identifying the mechanical behaviors of two new pre-heat treated steels of ESW95 and ESW105 and a conventional Cr-Mo steel of SCM435. The predictions are compared with the experiments for the tensile test of the three materials, showing an excellent similarity.

In this study, strong {0002} textured (or strong ND//<0002> textured) AZ31 Mg alloy sheets were prepared. These AZ31 Mg alloy sheets were cut along the angles of 0, 12.5, 25, 30 and 37.5 degrees to the rolling direction or {0002} texture. Prepared samples with different angles to the rolling direction were rolled at room temperature and after subsequent heat treatment, the bendability, ultimate tensile stress, elongation and texture are investigated using the 3-points bending tester, tensile tester and x-ray diffractometer, respectively. The specimen having along the angles of 0 degree to the rolling direction shows the highest load and 45 degrees specimen shows the highest displacement among any other specimens in the bending test. The specimen having along the angles of 12.5 and 25 degrees to the rolling direction shows highest elongation and of 0 degree specimen shows the highest ultimate tensile stress among any other specimens after cold rolling and subsequent heat treatment at 150°C for 30 minutes in bending test.

The microstructure, pole figure and r-value of the frictionally rolled and subsequently heat treated AA 5052 Al sheets were investigated by optical microscopy, x-ray diffractometer and tensile tester, respectively. Frictionally rolled AA 5052 Al specimens showed a fine grain size. After subsequently heat treated specimens, the ND//<111> texture component was increased. The r-values of the frictionally rolled and subsequently heat treated Al alloy sheets were about two times higher than those of the original Al sheets. These could be related to the formation of ND//<111> texture components through frictional rolling in and subsequent heat treatment of AA 5052 Al sheet.

Property of glass fiber reinforced polymer (GFRP) is naturally dependent on the property of matrix, but receives of temperature effects by external force. Therefore, determination of mechanical property by effect of temperature in GFRP is most crucial factor. In this paper, temperature distribution during crack propagation from temperature change under tensile test was proposed through IR thermography camera. Lock-in thermography method, which is one of technique in IR thermography camera to measure minute change in temperature, was utilized to monitor temperature distribution and change during crack propagation. Method to analyze temperature distribution during crack propagation under tensile test of GFRP via IR thermography camera was suggested. Anisotropy in fiber orientation showed longer fracture time and lower maximum temperature.